![](/v/vspfiles/templates/cctvcam-resp/images/DBox_Border_Left_Top.gif) |
![](/v/vspfiles/templates/cctvcam-resp/images/clear1x1.gif) |
![](/v/vspfiles/templates/cctvcam-resp/images/DBox_Border_Right_Top.gif) |
![](/v/vspfiles/templates/cctvcam-resp/images/clear1x1.gif) |
Please Note: The NET-SW8-4POE is no longer manufactured, please refer to the POE-SW88.
The NET-SW8-4POE Network Switch provides power and data from a single point,
using Power over Ethernet (PoE) over a single Cat-5 cable. This POE switch can be used to power up to 4 POE capable IP cameras. This switch has a total max output of 50 watts which works well because most IP cameras draw 12 watts. The eight
Fast Ethernet ports can be used for any 10/100/1000 Mbps link and four of
these ports can supply industry-standard IEEE 802.3af power. Advanced
auto-sensing algorithm gives power only to 802.3af end devices, so no
need to worry about damaging proprietary PoE or non-PoE equipment. In
addition, it discontinues the power when PoE devices are disconnected.
Easy and reliable, the NET-SW8-4POE automatically determines PoE
requirements, speed, duplex, and cable type.
The moderately priced NET-SW8-4POE delivers PoE to any small business
network that wants to simplify the installation of wireless access
points and
IP-based surveillance cameras. These devices are optimally
installed on a ceiling or high on a wall, away from most electrical
outlets. PoE eliminates the requirement for a dedicated electrical
outlet to power these devices. This allows for flexibility in situating
devices where AC power is difficult to access and lowers installation
costs. Compact and flexible, the NET-SW8-4POE is ideal for small
business networks that need to inexpensively use PoE to deploy wireless
access points and IP-based network surveillance cameras.
Typical Surveillance POE Network Switch Example
![POE Network Swith](/v/vspfiles/assets/images/network-example.jpg)
Flexible
Choose
to plug in up to eight Ethernet or Fast Ethernet devices and mix in up
to four 802.3af IP-based devices like wireless access points or
IP-based network surveillance cameras. Place these 802.3af-compliant
devices where they belong – high up on walls and ceiling for maximum
coverage – or anywhere else you need them. Power and data are carried
over standard Cat 5 cabling.
Plug and Play
The
standards-based NET-SW8-4POE senses and adjusts for network speed and
cabling type automatically, for easy integration into your existing
10/100/1000 Ethernet network. For PoE, the switch automatically detects
802.3af-compliant devices, and supplies power as needed. Front panel
LEDs keep you informed of switch and PoE status.
- Network Ports
- * 8 auto speed-sensing 10/100 RJ-45 ports
- Network Protocol and Standards
- * IEEE 802.3i 10BASE-T
- * IEEE 802.3u 100BASE-TX
- * IEEE 802.3x Flow Control
- * IEEE 802.3af DTE Power via MDI
- Performance Specifications
- * Forwarding modes: Store-and-forward
- * Bandwidth: 1.6 Gbps
- * Network latency: Less than 20 μs for 64-byte frames in store-and-forward mode for 100 Mbps to 100 Mbps transmission
- * Buffer memory: 96 KB embedded memory per unit
- * Address database size:1,000 media access control (MAC) addresses per system
- * Addressing: 48-bit MAC address
- * Mean Time Between Failure (MTBF): 190,000 hours (~ 21 years)
- * Acoustic Noise: 0 dB
- Status LEDs
- * System: Power, PoE Maximum Power
- * Per Port: Link, Activity, Speed, PoE Active, PoE Fault
- Power Supply
- * Total Power Consumption: 44 W maximum
- * PoE Watt budget: 32W
- * 802.3af Power Consumption: 32 W maximum (Ports 1 – 4)
- * 48VDC, 0.8A power output; plug is localized to country of sale
- Physical Specifications
- * Dimensions (H x W x D): 1.1 x 9.3 x 4.1 in. (27 x 235 x 103 mm)
- * Weight: 1.7 lbs. (0.74 kg)
- Environmental Specifications
- * Operating temperature: 32 to 104°F (0 to 40° C)
- * Storage temperature: 14 to 158°F (-10 to 70°C)
- * Operating humidity: 90% maximum relative humidity, non-condensing
- * Storage humidity: 95% maximum relative humidity, non-condensing
- * Operating altitude: 10,000 ft (3,000 m) maximum
- * Storage altitude: 10,000 ft (3,000 m) maximum
- Electromagnetic Emissions
- * CE mark, commercial
- * FCC Part 15 Class B
- * VCCI Class B
- * EN 55022 (CISPR 22), Class B
- * C-Tick
- Electromagnetic Immunity
- * EN 55024
- Safety
- * CE mark, commercial
- * CE/LVD EN60950
- Warranty
- * NETGEAR Lifetime Warranty†
- * 2 years for power supply
- Package Contents
- * ProSafe 8 Port 10/100 Switch with Power over Ethernet (FS108P)
- * AC Adapter
- * Wall-mount kit
- * Installation guide
- * Warranty/Support Information card
|
|
![](/v/vspfiles/templates/cctvcam-resp/images/clear1x1.gif) |
![](/v/vspfiles/templates/cctvcam-resp/images/DBox_Border_Left_Bottom.gif) |
![](/v/vspfiles/templates/cctvcam-resp/images/clear1x1.gif) |
![](/v/vspfiles/templates/cctvcam-resp/images/DBox_Border_Right_Bottom.gif) |
![](/v/vspfiles/templates/cctvcam-resp/images/clear1x1.gif)
|